This specification covers procedures for ultrasonic immersion inspection of premium-grade wrought titanium and titanium alloy round billet 5 inches (127 mm) and over in nominal diameter (see 2.6.1). Metal alloy billets other than titanium may be tested to this specification with the use of suitable reference standardsAMS K Non Destructive Methods and Processes Committee
The test method describes the procedure for the direct determination of water concentration in polyol ester and diester based aerospace lubricants by commercially available automated coulometric Karl Fischer titration instruments. The method was validated to cover the water concentration range of 150 to 3500 µg/g. The method may also be suitable for the determination of water concentrations outside this range and for other classes of fluids; however, the precision statement shall not be applicable for such usesE-34 Propulsion Lubricants Committee
Aluminum and its alloys entered a main role in the engineering sectors because of their applicable characteristics for indispensable applications. To enhance requisite belongings for the components, the composition of variant metal/nonmetal with light metal alloys is essential in the manufacturing industries. To enhance the wear resistance with significant strength property of the aluminum alloy 2024, the reinforcement SiC and fly ash (FA) were added with the designation Al2024 + 10% SiC; Al2024 + 5% SiC + 5% FA; and Al2024 + 10% FA via stir-casting technique. The wear resistance property of the composites was tested in pin-on-disc with a dry-sliding wear test procedure. The experiment trials were designed in Box–Behnken design (BBD) by differing the wear test parameters like % of reinforcement, sliding distance (m), and load (N). The wear tests on casted samples were carried out at the constant velocity of 2 m/sec, such that the corresponding wear rate for the experiment trials wasSivakumar, N., Sireesha, S. C., Raja, S., Ravichandran, P., Sivanesh, A. R., Aravind Kumar, R.
To investigate the rollover phenomena experienced by all-terrain vehicles (ATVs) during their motion caused by input from the road surface, a combined simulation using CarSim and Simulink has been employed to validate an active anti-rollover control strategy based on differential braking for ATVs, followed by vehicle testing. In the research process, a nonlinear three-degrees-of-freedom vehicle model has been developed. By utilizing a zero-moment point index as a rollover warning indicator, this approach could accurately detect the rollover status of the vehicle, particularly in scenarios involving low road adhesion on unpaved surfaces, which are characteristic of ATV operation. The differential braking, generating a roll moment by adjusting the amount of lateral force each braked tire can generate, was proved as an effective method to enhance rolling stability. Simulation and on-road testing results indicated that this control strategy effectively monitored the state of the ATV andHong, Hanchi, Wang, Kuan, d’Apolito, Luigi, Quan, Kangning, Yao, Xu
This specification establishes nondestructive testing methods, sampling frequency, and acceptance criteria for the inspection of metal castingsAMS B Finishes Processes and Fluids Committee
With globalization, vehicles are sold across the world throughout different markets and their automotive brake systems must function across a range of environmental conditions. Currently, there is no current standardized test that analyzes brake pads’ robustness against severe cold and humid environmental conditions. The purpose of this proposed test method is to validate brake system performance under severe cold conditions, comparing the results with ambient conditions to evaluate varying lining materials’ functional robustness. The goal of this paper is to aid in setting a standardized process and procedure for the testing of automotive brakes’ environmental robustness. Seven candidate friction materials were selected for analysis. The friction materials are kept confidential. Design of experiment (DOE) techniques were used to create a full-factorial test plan that covered all combinations of parameters. The test script involves brake applications at 5, 10, 15, and 20 bar, at bothPassador, Stephen Daniel Austin, Boudreau, Douglas Barret, Capacchione, Christopher James
The Particle Number–Portable Emission Measurement System (PN-PEMS) came into force with Euro VI Phase E regulations starting January 1, 2022. However, positive ignition (PI) engines must comply from January 1, 2024. The delay was due to the unavailability of the PN-PEMS system that could withstand high concentrations of water typically present in the tailpipe (TP) of CNG vehicles, which was detrimental to the PN-PEMS systems. Thus, this study was designed to evaluate the condensation particle counter (CPC)-based PN-PEMS measurement capabilities that was upgraded to endure high concentration of water. The PN-PEMS measurement of solid particle number (SPN23) greater than 23 nm was compared against the laboratory-grade PN systems in four phases. Each phase differs based upon the PN-PEMS and PN system location and measurements were made from three different CNG engines. In the first phase, systems measured the diluted exhaust through constant volume sampler (CVS) tunnel. Data generatedKhan, M. Yusuf, Agarwal, Nikhilesh, Panda, Sampad, Desai, Atharva Tushar, Wilkinson, John C., Chaille, Evan, Vats, Shekhar, Salemme, Tina L., Ragupathy, Thinnesh
This document describes a recommended test procedure to assess the burst characteristics of tires used on 14CFR Part 25 or similar transport airplanesA-5C Aircraft Tires Committee
In order to efficiently predict and investigate a vehicle’s vertical dynamics, it is necessary to consider the suspension component properties holistically. Although the effects of suspension stiffness and damping characteristics on vertical dynamics are widely understood, the impact of suspension friction in various driving scenarios has rarely been studied in both simulation and road tests for several decades. The present study addresses this issue by performing driving tests using a special device that allows a modification of the shock absorber or damper friction, and thus the suspension friction to be modified independently of other suspension parameters. Initially, its correct functioning is verified on a shock absorber test rig. A calibration and application routine is established in order to assign definite additional friction forces at high reproducibility levels. The device is equipped in a medium-class passenger vehicle, which is driven on various irregular road sections asDeubel, Clemens, Schneider, Scott Jarod, Prokop, Günther
Symbolic code execution is a powerful cybersecurity testing approach that facilitates the systematic exploration of all paths within a program to uncover previously unknown cybersecurity vulnerabilities. This is achieved through a Satisfiability Modulo Theory (SMT) solver, which operates on symbolic values for program inputs instead of using their concrete counterparts. However, in complex code bases, this approach faces significant limitations, such as program path explosions or unavailable dependencies, which can result in conditions that the SMT solver cannot reason about. Consequently, SMT solvers are often considered as too costly to implement for automotive testing use cases and are rarely employed within this domain. In contrast, fuzz testing has recently gained traction in the automotive industry as an invaluable testing technique for identifying previously unknown vulnerabilities. Its initial setup is straightforward and typically yields useful findings. However, achievingVinzenz, Nico, Oka, Dennis Kengo
Autonomous Vehicles are being widely tested under diverse conditions with expectations that they will soon be a regular feature on roads. The development of Autonomous Vehicles has become an important policy in countries around the world, and the technologies developed by countries and car manufacturers are different, and at the same time to adapt to the road environment and traffic management facilities of different countries, so some countries have built self-driving test sites, and the test content is also different, so it is impossible to compare its relative difficulty. This study surveyed experts and scholars to develop a means of weighting the respective difficulty of various autonomous vehicle testing conditions based on the analytic hierarchy process and fuzzy analytic hierarchy process, applied to a sample of 33 sets of testing conditions based on road type, management actions and operational capabilities. Weights are also adjusted in response to environmental impact factorsLin, Da-Jie, Liu, Hsin Hsien, CHOU, AI-CHEN, Huang, Pin-Cheng, WU, CHENG HSIN, CHANG, CHUN-YI, CHEN, MING-HSU
As part of the U.S. Environmental Protection Agency’s (EPA’s) continuing assessment of advanced light-duty automotive technologies in support of regulatory and compliance programs, a development project was started to study various test methods to benchmark Electric Drive Units (EDUs) consisting of an electric motor, inverter and a speed-reduction gearset. Several test methods were identified for consideration, including both in-vehicle testing of the complete EDU and stand-alone testing of the EDU and its subcomponents after removal from the vehicle. In all test methods explored, sweeps of speed and torque test points were conducted while collecting key EDU data required to determine efficiency, including motor torque and speed, direct current (DC) battery voltage and current into the inverter, and three-phase alternating current (AC) phase voltages and currents out of the inverter and into the electric motor. In addition, EDU operational data were collected to ensure consistentSchauer, Ethan, Moskalik, Andrew, Kargul, John, Stuhldreher, Mark, Butters, Karla, Barba, Daniel, Drallmeier, Joseph, Gross, Michael
In vehicle development, reducing noise is a major concern to ensure passenger comfort. As electric vehicles become more common and engine and vibration noises improve, the aerodynamic noise generated around the vehicle becomes relatively more noticeable. In particular, the fluctuating wind noise, which is affected by turbulence in the atmosphere, gusts of wind, and wake caused by the vehicle in front, can make passengers feel uncomfortable. However, the cause of the fluctuating wind noise has not been fully understood, and a solution has not yet been found. The reason for this is that fluctuating wind noise cannot be quantitatively evaluated using common noise evaluation methods such as FFT and STFT. In addition, previous studies have relied on road tests, which do not provide reproducible conditions due to changing atmospheric conditions. To address this issue, automobile manufacturers are developing devices to generate turbulence in wind tunnels. However, in wind tunnels, it isTajima, Atsushi, Ikeda, Jun, Nakasato, Kosuke, Kamiwaki, Takahiro, Wakamatsu, Junichi, Oshima, Munehiko, Li, ChungGang, Tsubokura, Makoto
The challenges concerning noise, vibration, and harshness (NVH) performance in the vehicle cabin have been significantly changed by the powertrain shift from a conventional drive unit with an internal-combustion engine (ICE) to electric drive units (eAxles). However, there is few research regarding the impact of electrification on NVH considering the influence of the context such as multi-stimuli and traffic rules during a real-life driving. In this study, the authors conducted test drives using EVs and ICEVs on public roads in Europe and conducted a statistical analysis of the difference in driver impression of NVH performance based on interviews during actual driving. The impression data were categorized into clusters corresponding to related phenomena or features based on driver comments. Furthermore, the vehicles data (vehicle speed, acceleration, GPS information, etc.) were recorded to associate the driver impressions with the vehicle’s conditions when the comments were madeMise, Shion, Torii, Kenji, Sellerbeck, Philipp, Hank, Stefan, Iwano, Hidetaka, Nishikoji, Takuya
Driver Assistance and Autonomous Driving features are becoming nearly ubiquitous in new vehicles. The intent of the Driver Assistant features is to assist the driver in making safer decisions. The intent of Autonomous Driving features is to execute vehicle maneuvers, without human intervention, in a safe manner. The overall goal of Driver Assistance and Autonomous Driving features is to reduce accidents, injuries, and deaths with a comforting driving experience. However, different drivers can react differently to advanced automated driving technology. It is therefore important to consider and improve the adaptability of these advances based on driver behavior. In this paper, a human-centric approach is adopted to provide an enriching driving experience. We perform data analysis of the naturalistic behavior of drivers when performing lane change maneuvers by extracting features from extensive Second Strategic Highway Research Program (SHRP2) data of over 5,400,000 data files. First, theLakhkar, Radhika Anandrao, Talty, Tim
The current focus in the ongoing development of autonomous driving systems (ADS) for heavy duty vehicles is that of vehicle operational safety. To this end, developers and researchers alike are working towards a complete understanding of the operating environments and conditions that autonomous vehicles are subject to during their mission. This understanding is critical to the testing and validation phases of the development of autonomous vehicles and allows for the identification of both the nominal and edge case scenarios encountered by these systems. Previous work by the authors saw the development of a comprehensive scenario generation framework to identify an operating domain specification (ODS), or external and internal conditions an autonomous driving system can expect to encounter on its mission to form critical scenario groups for autonomous vehicle testing and validating using statistical patterns, clustering, and correlation. Continuing this prior work, this paper focuses onSiekmann, Adam, Miller, Brandon, Sujan, Vivek, Moore, Amy
Modern advances in the technical developments of Advanced Driver Assistance Systems (ADAS) have elevated autonomous vehicle (AV) operations to a new height. Vehicles equipped with sensor based ADAS have been positively contributing to safer roads. As the automotive industry strives for SAE Level 5 full driving autonomy, challenges inevitably arise to ensure ADAS performance and reliability in all driving scenarios, especially in adverse weather conditions, during which ADAS sensors such as optical cameras and LiDARs suffer performance degradation, leading to inaccuracy and inability to provide crucial environmental information for object detection. Currently, the difficulty to simulate realistic and dynamic adverse weather scenarios experienced by vehicles in a controlled environment becomes one of the challenges that hinders further ADAS development. While outdoor testing encounters unpredictable environmental variables, indoor testing methods, such as using spray nozzles in a windLi, Long, Pao, Wing Yi, Howorth, Joshua, Agelin-chaab, Martin, Roy, Langis, Komar, John, Knutzen, Julian, Baltazar, Alex, Muenker, Klaus
With the development of vehicles equipped with automated driving systems, the need for systematic evaluation of AV performance has grown increasingly imperative. According to ISO 34502, one of the safety test objectives is to learn the minimum performance levels required for diverse scenarios. To address this need, this paper combines two essential methodologies - scenario-based testing procedures and scoring systems - to systematically evaluate the behavioral competence of AVs. In this study, we conduct comprehensive testing across diverse scenarios within a simulator environment following Mcity AV Driver Licensing Test procedure. These scenarios span several common real-world driving situations, including BV Cut-in, BV Lane Departure into VUT Path from Opposite Direction, BV Left Turn Across VUT Path, and BV Right Turn into VUT Path scenarios. Furthermore, the test cases are divided into different risk levels, allowing the AV to be tested in a variety of risk-level situations, with aWang, Tinghan, Rahimi, Shujauddin, Swaminathan, Sunder, Zaidi, Mohsin, Wishart, Jeffrey, Liu, Henry
Common aerodynamic research models have been used in aerodynamic research throughout the years to assist with the development and correlation of new testing and numerical techniques, in addition to being excellent tools for gathering fundamental knowledge about the physics around the vehicle. The generic truck utility (GTU) was introduced by Woodiga et al. [1] in 2020 following successful adoption of the DrivAer (Heft et al. [2]) by the automotive aerodynamics community with the goal to capture the unique flow fields created by pickups and large SUVs. To date, several studies have been presented on the GTU (Howard et. al 2021 [3], Gleason, Eugen 2022 [4]), however, with the increasing prevalence of electric vehicles (EVs), the authors have created additional GTU configurations to emulate an EV-style underbody for the GTU. The existing GTU has the flexibility to independently vary the cab and box lengths, plus a rear cap with three different backlight angles to model SUVs, however, theHoward, Kevin, Chen, Sheng, Dobronsky, Sayan, Kochanek, Zachary, Skinner, Shaun
The context for real-world emissions compliance has widened with the anticipated implementation of EU7 emissions regulations. The more stringent emissions limits and deeper real-world driving test fields of EU7 make compliance more challenging. While EU6 emissions legislation provided clear boundaries by which vehicle and powertrain Original Equipment Manufacturers (OEMs) could develop and calibrate against, EU7 creates additional challenges. To ensure that emissions produced during any real-world driving comply with legal limits, physical testing conducted in-house and in-field to evaluate emissions compliance of a vehicle and powertrain will not be sufficient. Given this, OEMs will likely need to incorporate some type of virtual engineering to supplement physical testing. In this respect, the HORIBA Intelligent Lab virtual engineering toolset has been created and deployed to produce empirical digital twins of a modern light-duty electrified gasoline Internal Combustion Engine (ICERoberts, Phil, Mason, Alex, Headley, Aaron, Bates, Luke, Tabata, Kunio, Whelan, Steve