This document presents a study on the design and simulation of a high-lift airfoil intended for usage in multielement setups such as the wings present on open-wheel race cars. With the advancement of open-wheel race car aerodynamics, the design of existing high-lift airfoils has been altered to create a more useful and practical general profile. Adjoint optimization tools in CFD (ANSYS Fluent) were employed to increase the airfoil’s performance beyond existing high-lift profiles (Selig S1223). Improvements of up to 20% with a CL of 2.4 were recorded. To further evaluate performance, the airfoil was made the basis of a full three-dimensional aerodynamics package design for an open-wheel Formula Student car. CFD simulations were carried out on the same and revealed performance characteristics of the airfoil in a more practical application. These CFD simulations were calibrated with experimental values from coast-down testing data with an accuracy of 8Karthikeyan, Prthik Nandhan, Radhakrishnan, Jayakrishnan
The automotive sector’s growing focus on sustainability has been spurred to investigate the creation of sustainable resources for different parts, emphasizing enhancing efficiency and minimizing environmental harm. For use in automobile flooring trays and underbody shields, this study examines the impact of injection molding on composite materials made of polyvinyl chloride (PVC) and Linum usitatissimum (flax) fibers. As processed organic fiber content was increased, the bending and tensile rigidity initially witnessed an upsurge, peaking at a specific fiber loading. At this optimal loading, the composite exhibited tensile strength, flexural strength, and elastic modulus values of 41.26 MPa, 52.32 MPa, and 2.65 GPa, respectively. Given their deformation resistance and impact absorption attributes, the mechanical properties recorded suggest that such composites can be efficiently utilized for automotive underbody shields and floor trays. The inherent structure of the flax fiber withinNatrayan, L., Kaliappan, Seeniappan, Balaji, V., Mahesh, V.
The analysis presented in this document demonstrates the mathematical model approach for determining the rotation of a door about the hinge axis. Additional results from the model are the torque due to gravity about the axis, opening force, and the door hold open check link force. Vector mechanics, equations of a plane, and parametric equations were utilized to develop this model, which only requires coordinate points as inputs. This model allows for various hinge axis angles and door rotation angles to quickly be analyzed. Vehicle pitch and roll angles may also be input along with door mass to determine the torque about the hinge axis. The vector calculations to determine the moment arm of the door check link and its resulting force are demonstrated for both a standard check link design and an alternate check link design that has the link connected to a slider translated along a shaft. This math model may be implemented using commonly available programs such as Microsoft Excel VBA orStorck, Phillip
This SAE Aerospace Standard (AS) sets forth criteria for the selection and verification processes to be followed in providing tires that will be suitable for intended use on civil aircraft. This document encompasses new and requalified radial and bias aircraft tiresA-5C Aircraft Tires Committee
Mechanical drawing plays an important role in managing, designing and implementing engineering projects, especially in the field of the automotive industry. The need for accuracy in element design and manufacturing is greater now than ever before in engineering industries. In order to increase accuracy, the part design and function must be clearly communicated between the design engineer and the manufacturing technicians, especially in automotive industry and feeder industries projects. Geometric Dimensions and Tolerances (GD&T) system of elements determines the quality, importance and price of the designed product. The standard used in the United States to define GD&T methodology is ASME Y14.5-2009 while the standard used in Europe is ISO 1101-2017. This article discussed the importance of using GD&T system including the types of geometrical features, limitations and accuracy, datum references frame and feature control frame to handle these symbols seamlessly. Moreover, the paperAli, Amr S.H.R., Ali, Akram M. S., Amin, Youssef W.R., Ali, Salah H. R.
The present study introduces a novel approach for achieving path tracking of an unmanned bicycle in its local body-fixed coordinate frame. A bicycle is generally recognized as a multibody system consisting of four distinct rigid bodies, namely the front wheel, the front fork, the body frame, and the rear wheel. In contrast to most previous studies, the relationship between a tire and the road is now considered in terms of tire forces rather than nonholonomic constraints. The body frame has six degrees of freedom, while the rear wheel and front fork each have one degree of freedom relative to the body frame. The front wheel exhibits a single degree of freedom relative to the front fork. A bicycle has a total of nine degrees of freedom. The expression of the kinetic energy of a bike is formulated using quasi-coordinates in the local body-fixed coordinate frame, which provides a more simplified representation compared to the utilization of absolute coordinates in the global coordinateCheng, Kaizhuo, Duan, Yupeng, Wu, Jinglai, Zhang, Yunqing
The design of lightweight vehicle structures has become a common method for automotive manufacturers to increase fuel efficiency and decrease carbon emission of their products. By using aluminum instead of steel, manufacturers can reduce the weight of a vehicle while still maintaining the required strength and stiffness. Currently, Resistance Spot Welding (RSW) is used extensively to join steel body panels but presents challenges when applied to aluminum. When compared to steel, RSW of aluminum requires frequent electrode cleaning, higher energy usage, and more controlled welding parameters, which has driven up the cost of manufacturing. Due to the increased cost associated with RSW of aluminum, Refill Friction Stir Spot Welding (RFSSW) is being considered as an alternative to RSW for joining aluminum body panels. RFSSW consumes less energy, requires less maintenance, and produces more consistent welding in aluminum as compared to RSW. Research has shown that RFSSW is capable ofGale, Damon, Hovanski, Yuri, Coyne, Jeremy, Namola, Kate
Side doors are pivotal components of any vehicle, not only for their aesthetic and safety aspects but also due to their direct interaction with customers. Therefore, ensuring good structural performance of side doors is crucial, especially under various loading conditions during vehicle use. Among the vital performance criteria for door design, torsional stiffness plays an important role in ensuring an adequate life cycle of door. This paper focuses on investigating the impact of several door structural parameters on the torsional stiffness of side doors. These parameters include the positioning of the latch, the number of door side hinge mounting points on doors (single or double bolt), and the design of door inner panel with or without Tailor Welded Blank (TWB) construction. The findings of this study reveal that the change in latch position has the most significant influence on torsional stiffness, followed by the removal of TWB from the inner panel, upon implementation of suitableGoyal, Vinay Kumar, Selvan, Veera, Pandurangan, Venugopal, Unadkat, Siddharth, Almeida, Neil Ricardo
Collisions resulting in injuries or fatalities occur more frequently at intersections. This is partly because safe navigation of intersections requires drivers to accurately observe and respond to other road users with conflicting paths. Previous studies have raised questions about how traffic control devices and the positioning of other road users might affect drivers' visual search strategies when navigating intersections. To address these questions, four left-turn-across-path (LTAP) scenarios were created by combining two types of traffic control devices (stop signs and traffic lights) with two hazard starting locations (central and peripheral). Seventy-four licensed drivers responded to all scenarios in a counterbalanced order using a full vehicle driving simulator. Eye-tracking glasses were used to monitor eye movements, both before and after hazard onset. The results revealed that drivers at the signalized intersections took longer to fixate the LTAP hazard before onset, spentCaren, Brooklin, Ziraldo, Erika, Oliver, Michele
In the context of vehicle electrification, improving vehicle aerodynamics is not only critical for efficiency and range, but also for driving experience. In order to balance the necessary trade-offs between drag and downforce without significant impact on the vehicle styling, we see an increasing amount of active aerodynamic solutions on high-end passenger vehicles. Active rear spoilers are one of the most common active aerodynamic features. They deploy at high vehicle speed when additional downforce is required [1, 2]. For a vehicle with an active rear spoiler, the aerodynamic performance is typically predicted through simulations or physical testing at different static spoiler positions. These positions range from fully stowed to fully deployed. However, this approach does not provide any information regarding the transient effects during the deployment of the rear spoiler, which can be critical to understanding key performance aspects of the system. In this paper, we propose aFougere, Nicolas, DeMeo, Michael, Tuit Farquhar, Henry, Oliveira, Danilo, Nastov, Alexander
In the early stages of vehicle development, it is critical to establish performance goals for the major systems. The fundamental modes of body and chassis frames are typically assessed using FE models that are discretized using shell elements. However, the use of the shell-based FE method is problematic in terms of fast analysis and quick decision-making, especially during the concept phase of a vehicle design because it takes much time and effort for detailed modeling. To overcome this weakness, a one-dimensional (1D) method based on beam elements has been extensively studied over several decades, but it was not successful because of low accuracy for thin-walled beam structures. This investigation proposes a 1D method based on thin-walled beam theory with comparable accuracy to shell models. Most body pillars and chassis frame members are composed of thin-walled beam structures because of the high stiffness-to-mass ratio of thin-walled cross sections. However, thin-walled crossKim, Jin Hong, Lee, Dong Ki, Kim, Gyu Sik, Jang, Gang-Won, Kim, Han Kil
The new idea discussed in this paper pertains to the carrier mechanism for spare wheels in heavy commercial vehicles. Typically, these vehicles are equipped with a spare wheel carrier featuring a rope mechanism for loading and unloading the spare wheel. The conventional placement of this system is on the side of the frame/chassis or within the limits of the side member. However, the tire-changing process in this system is often arduous, time-consuming, and requires significant effort. The proposed invention addresses these challenges by repositioning the spare wheel to a vertical orientation, facilitating easier access to its bolts and simplifying the removal process from the mountings. Furthermore, the innovation incorporates a three-way actuation system (Air Actuated, Electric motor-driven, or Hydraulic cylinder actuated mechanisms), thereby reducing the need for manual effort and enhancing driver comfort. The advantages of this invention over traditional carrier mechanisms includeBonde, Devendra, Upkare, Piyush Pradip, Verma, Rubal
This paper analyzes the mechanism of vibrational energy propagation and panel vibration generation at the point joints between frame and panel which can be applied to reduce the vehicle interior noise. In this study, we focused on the traveling wave in the early stage of propagation before the mode is formed and investigated the mechanism of panel vibration generation due to wave energy propagation and its reduction method. First, we show theoretically that the out-of-plane component of the transmitted power at the point joint between frame and panel that contributes to panel vibration is associated with frame deformation. Then, we show through numerical verification that panel vibration can be reduced by reducing the transmitted power of the out-of-plane component and explain the effectiveness of the frame-to-panel joint design guidelines based on energy propagation analysis. Next, this analysis method was applied to the vehicle body FEM model. Assuming road noise, an energyAbe, Keisuke, Tanaka, Yunosuke, Yamazaki, Toru
The origami structures have received increasing attention in recent years due to the high stiffness ratio and lightweight feature. This paper has proposed an origami-based honeycomb structure and investigated the mechanical properties of the structure. The compression response and energy absorption of the structure under quasi-static loading have been investigated experimentally and numerically. The numerical results closely matched the experimental results in terms of the compression force curve and deformation patterns. The effects of different structural parameters on the mechanical response and energy absorption characteristics were analyzed with the validated model. Finally, the comparative results show that the origami-inspired honeycomb structure, which is characterized by rotational folding mode under axial compression, has better performance in terms of mechanical response and energy absorption. Two parameters, the thickness and the height have a greater influence on theWu, Pengjiang, Wu, Chunfu, Ye, Guorui, Zhao, Yonghong, Ye, Baowen, Wang, Liangmo, Wang, Tao, Zhang, Zeming
A crucial component utilized in the trunk space is the luggage board. Positioned at the bottom of the trunk, the trunk board separates the vehicle body from the interior and supports for luggage. The luggage board serves multiple functions, including load-bearing stiffness for luggage, partition structure functionality, noise insulation, and thermal insulation. There is a need for a competitive new luggage board manufacturing method to meet the increasing demand for luggage boards in response to the changing market environment. To address this, the "integrated sandwich molding method" is required. The integrated sandwich molding method utilizes three key methodologies: grouping processes to integrate similar functions, analyzing materials to replace them with suitable alternatives, and overcoming any lacking functionality through integrated design structures. This paper presents a methodology for developing the integrated sandwich molding method. It aims to validate the key performancePark, Hee Sang, Yoon, Yeon Sim, Lee Sr, Seung Kun, Kim Sr, Seok Cheol, Lee, Dong Han
SLAM (Simultaneous Localization and Mapping) plays a key role in autonomous driving. Recently, 4D Radar has attracted widespread attention because it breaks through the limitations of 3D millimeter wave radar and can simultaneously detect the distance, velocity, horizontal azimuth and elevation azimuth of the target with high resolution. However, there are few studies on 4D Radar in SLAM. In this paper, RI-FGO, a 4D Radar-Inertial SLAM method based on Factor Graph Optimization, is proposed. The RANSAC (Random Sample Consensus) method is used to eliminate the dynamic obstacle points from a single scan, and the ego-motion velocity is estimated from the static point cloud. A 4D Radar velocity factor is constructed in GTSAM to receive the estimated velocity in a single scan as a measurement and directly integrated into the factor graph. The 4D Radar point clouds of consecutive frames are matched as the odometry factor. A modified scan context method, which is more suitable for 4D Radar’sZihang, He, Xiong, Lu, Zhuo, Guirong, GAO, Letian, Lu, Shouyi, Zhu, Jiaqi, Leng, Bo
The side-door operation of vehicle is vital to the customer, as it reflects the overall build quality of the vehicle. The side door check arm is one of the primary components that determine the operating characteristics of a vehicle door. The profile of the check arm has a significant impact on the closing effort of side doors. In this study, the check arm profiles are analyzed virtually in relation to the side door's closing velocity. A virtual door model was developed in ADAMS to simulate the side door closing and opening. The study involves a check arm that guides the ball spring mechanism housing unit over the guide profile. Typically, a check-arm guide profile has two or three indents at a specific location which serves to maintain the door open in those positions. When a door enters an indent, the user must exert an effort to traverse it. Furthermore, the slope profile of the check arm defines the self-closing assist offered from the initial indent to the latching position. ByKeshav T J, Sharath, Selvan, Veera, Unadkat, Siddharth, Subbaiyan, Prasanna Balaji, Pandurangan, Venugopal, Nizampatnam, Balaramakrishna
This paper addresses the issues of long-term signal loss in localization and cumulative drift in SLAM-based online mapping and localization in autonomous valet parking scenarios. A GPS, INS, and SLAM fusion localization framework is proposed, enabling centimeter-level localization with wide scene adaptability at multiple scales. The framework leverages the coupling of LiDAR and Inertial Measurement Unit (IMU) to create a point cloud map within the parking environment. The IMU pre-integration information is used to provide rough pose estimation for point cloud frames, and distortion correction, line and plane feature extraction are performed for pose estimation. The map is optimized and aligned with a global coordinate system during the mapping process, while a visual Bag-of-Words model is built to remove dynamic features. The fusion of prior map knowledge and various sensors is employed for in-scene localization, where a GPS-fusion Bag-of-Words model is used for vehicle poseChen, Guoying, Wang, Ziang, Gao, Zheng, Yao, Jun, Wang, Xinyu
Reliable and safe Redundant Steering System (RSS) equipped with Dual-Winding Permanent Magnet Synchronous Motor (DW-PMSM) is considered an ideal actuator for future autonomous vehicle chassis. The built-in DW-PMSM of the RSS is required to identify various winding’s faults such as disconnection, open circuit, and grounding. When achieving redundant control through winding switching, it is necessary to suppress speed fluctuations during the process of winding switching to ensure angle control precision. In this paper, a steering angle safety control for RSS considering motor winding’s faults is proposed. First, we analyze working principle of RSS. Corresponding steering system model and fault model of DW-PMSM have been established. Next, we design the fault diagnosis and fault tolerance strategy of RSS. Considering the difference in amplitude frequency characteristics of phase current during DW-PMSM winding faults, the Hanning window and Short-Time Fourier Transform (STFT) isZhao, Jian, Dang, Ruijie, Wu, Hangzhe, Zhu, Bing, Chen, Zhicheng
A variety of structures resonate when they are excited by external forces at, or near, their natural frequencies. This can lead to high deformation which may cause damage to the integrity of the structure. There have been many applications of external devices to dampen the effects of this excitation, such as tuned mass dampers or both semi-active and active dampers, which have been implemented in buildings, bridges, and other large structures. One of the active cancellation methods uses centrifugal forces generated by the rotation of an unbalanced mass. These forces help to counter the external excitation force coming into the structure. This research focuses on active force cancellation using centrifugal forces (CFG) due to mass imbalance and provides a virtual solution to simulate and predict the forces required to cancel external excitation to an automotive structure. This research tries to address the challenges to miniaturize the CFG model for a body-on-frame truck. The virtualPaul, Abhishek, Latcha, Michael
The Insurance Institute for Highway Safety (IIHS) introduced its updated side-impact ratings test in 2020 to address the nearly 5,000 fatalities occurring annually on U.S. roads in side crashes. Research for the updated test indicated the most promising avenue to address the remaining real-world injuries was a higher severity vehicle-to-vehicle test using a striking barrier that represents a sport utility vehicle. A multi-stiffness aluminum honeycomb barrier was developed to match these conditions. The complexity of a multi-stiffness barrier design warranted research into developing a new dynamic certification procedure. A dynamic test procedure was created to ensure product consistency. The current study outlines the process to develop a dynamic barrier certification protocol. The final configuration includes a rigid inverted T-shaped fixture mounted to a load cell wall. This fixture is impacted by the updated IIHS moving deformable barrier at 30 km/h. The fixture represents the stiffMueller, Becky, Arbelaez, Raul, Heitkamp, Eric, Mampe, Christopher
To ensure adequate visibility without excessive glare, vehicle headlights are designed to use a specific source of illumination. The optical designs of headlights gather the luminous flux produced by the light source to produce a useful beam pattern that meets the relevant requirements and standards for vehicle forward lighting. With the advent of solid state, light emitting diode sources for general illumination, an increasing number of LED replacement headlight bulb products has emerged over the past decade. In most cases, these LED replacement bulbs are not permitted for legal use on public roadways, but some countries have begun to permit specific LED replacement bulbs to be used legally on the road for specific makes, models and production years of certain vehicles. If they can be demonstrated to produce a beam pattern that meets the photometric requirements for a legal headlight, they are permitted to be used legally for on-road use. In the present paper we present photometricBullough, John D., Skinner, Nicholas P.
In the process of designing the aerodynamic kit for Formula SAE racing cars, there is a lot of repetitive work and low efficiency in optimizing parameters such as wing angle of attack and chord length. Moreover, the optimization of these parameters in past designs heavily relied on design experience and it's difficult to achieve the optimal solution through theoretical calculations. By establishing a parametric model in CAD software and integrating it with CFD software, we can automatically modify model parameters, run a large number of simulations, and analyze the simulation results using statistical methods. After multiple iterations, we achieve fully automatic parameter optimization and obtain higher negative lift. At the same time, the simulation process is optimized, and simulations are run based on GPUs, resulting in a significant increase in simulation speed compared to the original. The results show that automated optimization saves a lot of manpower costs, and compared toChen, Yanjun
In electric vehicle applications, the majority of the traction motors can be categorized as Permanent Magnet (PM) motors due to their outstanding performance. As indicated in the name, there are strong permanent magnets used inside the rotor of the motor, which interacts with the stator and causes strong magnetic pulling force during the assembly process. How to estimate this magnetic pulling force can be critical for manufacturing safety and efficiency. In this paper, a full 3D magnetostatic model has been proposed to calculate the baseline force using a dummy non-slotted cylinder stator and a simplified rotor for less meshing elements. Then, the full 360 deg model is simplified to a half-pole model based on motor symmetry to save the simulation time from 2 days to 2 hours. A rotor position sweep was conducted to find the maximum pulling force position. The result shows that the max pulling force happens when the rotor is 1% overlapping with the stator core. The impact of asymmetricGong, Cheng, Chang, Le, He, Song, Zhang, Peng, Muir, Michael
Tradespace exploration (TSE) describes the activity occurring early in the design process through which stakeholders explore a broad solution space in search of more-optimal alternatives. In doing so, these stakeholders attempt to maximize the utility inherent in the chosen solution while understanding the tradeoffs and compromises that may be required to find an acceptable solution. In the field of vehicle design, tradespaces are often comprised of vast amounts of alternatives which increases the complexity of the decision-making process. Additionally, the number of stakeholders has grown, as decision-makers seek to include more variety in both perspectives and expertise. As such, decision-making stakeholders can often find themselves working at odds and attempting to maximize vastly different objectives in the process. One way to rectify these contrasting viewpoints can be to intentionally introduce a group framing prior to the start of decision making. In this experiment, teams ofSutton, Meredith, Turner, Cameron, Hartman, Gregory, Gorsich, David, Skowronska, Annette
The transition towards battery electric vehicles (BEVs) has increased the focus of vehicle manufacturers on energy efficiency. Ensuring adequate airflow through the heat exchanger is necessary to climatize the vehicle, at the cost of an increase in the aerodynamic drag. With lower cooling airflow requirements in BEVs during driving, the front air intakes could be made smaller and thus be placed with greater freedom. This paper explores the effects on exterior aerodynamics caused by securing a constant cooling airflow through intakes at various positions across the front of the vehicle. High-fidelity simulations were performed on a variation of the open-source AeroSUV model that is more representative of a BEV configuration. To focus on the exterior aerodynamic changes, and under the assumption that the cooling requirements would remain the same for a given driving condition, a constant mass flow boundary condition was defined at the cooling airflow inlets and outlets. A parametricUpadhyaya, Avaneesh, Sebben, Simone, Willeson, Emil, Minelli, Guglielmo
The rotor and stator of electric motors consist of multiple materials, of which steel forms the majority of mass and volume. Steel in electric motors is commonly in the form of thin sheets (laminations), stacked along the axis of the rotor. The structural integrity of such a stack can be ensured using bolting, welding or bonding of the laminations. Predictive mechanical finite element simulations of these laminated stacks can become computationally intense because the steel sheets are thin, and the motor often contains hundreds of them. If the laminations are modelled individually, the size of the elements is very small compared to the overall dimensions and the interface between the laminations need to be modelled as well. In this paper, we present an alternate method of modelling this laminated stack as a single solid body using homogeneous and orthotropic material property, instead of representing each lamination. This provides realistic predictions of mechanical performance, whileGoel, Ashish, P, Praveen, Sharma, Hiren, Faggioli, Thiago
Automotive body structures are being increasingly made in multi-material system consisting of steel, aluminum (Al) and fiber-reinforced plastics (FRP). Therefore, many joining techniques such as self-piercing riveting (SPR) and adhesive bonding have been developed. On the other hand, OEMs want to minimize the number of joining techniques to reduce the manufacturing complexity. Amount all joining methods, resistance spot welding (RSW) is the most advanced and cost-effective one for body-in-white. However, RSW cannot be applied for joining dissimilar materials. Therefore, a novel Rivet Resistance Spot Welding method (RRSW) was developed in which Al or FRP components can be directly welded to steel structures with existing welding systems. RRSW uses rivet-like double T-shaped steel elements as a welding adapter which are formed or integrated into Al or FRP components during their forming process. After that, they are welded to the steel components by RSW. This paper shows at first theFang, Xiangfan, Zhang, Fan, Xu, Hongli
The modern luxurious electric vehicle (EV) demands high torque and high-speed requirements with increased range. Fulfilling these requirements gives rise to the need for increased efficiency and power density of the motors in the Electric Drive Unit (EDU). Internal Permanent Magnet (IPM) motor is one of the best suited options in such scenarios because of its primary advantages of higher efficiency and precise control over torque and speed. In the IPM motor, permanent magnets are mounted within the rotor body to produce a resultant rotating magnetic field with the 3-phase AC current supply in the stator. IPM configuration provides structural integrity and high dynamic performance as the magnets are inserted within the rotor body. Adhesive glue is used to install the magnets within the laminated stack of rotor. High rotational speed of rotor introduces centrifugal loading on the magnets which can result in multiple failure modes such as the debonding of the magnet, and high radialKarmakar, Nilankan, P, Praveen, Goel, Ashish
Wound rotor synchronous machines (WRSM) without rare-earth magnets are becoming more popular for traction applications, but their potential in drive performance has not yet been fully explored. This paper presents a Pulse Width Modulation (PWM) scheme optimization procedure to minimize motor and inverter losses. It leverages different PWM schemes with different PWM switching strategies and switching frequencies. First, a generic PWM-induced motor loss calculation tool developed by BorgWarner is introduced. This tool iteratively calculates motor losses with PWM inputs across the entire operating map, significantly improving motor loss prediction accuracy. The inverter losses are then calculated analytically using motor and wide-bandgap (WBG) switching device characteristics. By quantifying these various scenarios, the optimal PWM scheme for achieving the best system efficiency across the entire operating map is obtained. The PWM-induced motor loss characteristics, the system lossMa, Cong, Tyckowski, Joseph
The recent surge in platforms like YouTube has facilitated greater access to information for consumers, and vehicles are no exception, so consumers are increasingly demanding of the quality of their vehicles. By the way, the door is composed of glass, moldings, and other parts that consumers can touch directly, and because it is a moving part, many quality issues arise. In particular, the door panel is assembled from all of the above-mentioned parts and thereby necessitates a robust structure. Therefore, this study focuses on the structural stiffness of the door inner panel module mounting area because the door module is closely to the glass raising and lowering, which is intrinsically linked to various quality issuesCho, Kyeongkuk, Choi, JEWON
Certain sports utility vehicles (SUVs) utilize dual latches and gas struts in their hood design. This is primarily driven by the larger size of the hood and specific architectural requirements. These hoods can be securely latched either by a dynamic single stroke closing method or by quasistatic two stroke closing method. In dynamic method, the hood is closed with a single, high-velocity motion for the final primary latching, whereas in quasistatic method, force is initially applied for the secondary latching and then for the final primary latching. In this study, both the dynamic and quasistatic closing methods are compared in terms of closing force and velocity and hood over travel distance. A load cell is used for measuring the closing force, velocity meter is used for velocity measurement and a rope sensor is used for measuring the hood over travel distance. It is evident from the study that the velocity required for hood closing is higher in the dynamic method, than the quasiSelvan, Veera, Sakthivel, Gowtham, R, Balaji, AS, Kevin, A, Sankaranarayanan, Kamat, Rohan, Unadkat, Siddharth, Pandurangan, Venugopal